Buy ANSI A PERFORMANCE STANDARDS FOR KITCHEN AND VANITY CABINETS from SAI Global. Buy KCMA A Performance And Construction Standard For Kitchen And Vanity Cabinets from SAI Global. Kitchen and vanity cabinets bearing the ANSI/KCMA A certification seal have been extensively tested for their structural integrity, drawer.
|Published (Last):||7 December 2015|
|PDF File Size:||2.74 Mb|
|ePub File Size:||18.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
The cabinet door must operate as before the asi and show no damage or sign of separation or failure in the system. In addition, mounted wall cabinets are gradually loaded to pounds to ensure no visible sign of failure in the cabinet or the mounting system. A load of up to pounds is applied against the aansi of cabinet fronts to ensure reliable front joints. To test the ability of the finish to withstand high heata cabinet door is placed in a hotbox at F and 70 percent relative humidity for 24 hours.
The strength behind certified cabinetry: ANSI/KCMA A | Woodworking Network
The drawers must then remain operable with no failure in any part a61.1 the drawer assembly or operating system, and drawer bottoms must not be deflected to interfere with drawer operation. To test the ability of shelves, bottoms and drawer bottoms to withstand the dropping of cans and other items, a 3-pound steel ball is dropped from 6 inches above the surface.
Your recommendation is being sent! A 3 pound weight is dropped 10 times against the drawer assembly to ensure that the drawer front assembly will withstand the impact of closing. Please refine your selection. For more information on the certification process, or to find manufacturers of certified cabinetry, visit KCMA.
KCMA has sponsored the nationally recognized cabinet testing and certification program for more than ansl years. Share your thoughts with us in the comments below. This ensures the cabinets will live up to your expectations. Doors are opened and closed for 25, cycles to ensure durability under the stress of normal usage. For information on the certification or to locate a certified cabinet manufacturer, visit the Certifications portal at KCMA.
View the discussion thread.
Cabinet finishes are inspected to ensure that stringent standards of appearance are also met. Installed wall cabinets are loaded with pounds to ensure that the cabinet will accept net loading in compliance with ANSI A The s161.1 must then show no appreciable discoloration and no evidence of blistering, cold checking, or other film failure.
The strength behind certified cabinetry: ANSI/KCMA A161.1
To test the strength of base-front joints, a load of pounds is applied against the inside of cabinet-front stiles for cabinets with a drawer rail, or pounds for cabinets without a drawer rail, to ensure reliable front joints that will not open during stress in service or during installation. Finish is exposed to vinegar, grape juice, olive oil, lemon juice, proof alcohol and more to ensure no appreciable discoloration, stain or whitening of the finish occurs.
The door must remain weighted for 10 minutes, after which the door and hinges must show no visible signs of damage, and connections between cabinet-and-hinge and door-and-hinge must show no sign of looseness.
The door edge must then show no delamination or swelling and no appreciable discoloration or evidence of blistering, checking, whitening, or other film failure. Cabinets are impact tested by striking the center of a closed and open door with a 10 pound sand bag.
Have something to say? Cabinet doors are weighted with 65 pounds and operated 10 times to test the ability of door and hinges to withstand loading.
The maximum number of products that can be compared is 4.
To test the ability of drawers and drawer mechanisms to operate with loading during normal use, drawers are loaded at 15 pounds per square foot and operated through 25, cycles.
After 10 drops, there must be no evidence of looseness or structural damage to the drawer-front assembly that impairs its operation. These tests create, in accelerated form, the cumulative effects of years of normal kitchen conditions of pre-finished cabinets. After the test the drawer must not be damaged and must operate as before the test, with no visible sign of joint separation or failure of any part of the cabinet or mounting system. Your Email has been successfully sent! The cycle is repeated five times.
In order to be certified, cabinets must also undergo eight categories of testing, covering structural integrity, drawer and door operation and finish quality see sidebar below.
To test the ability of cabinet doors and connections to withstand impacts such as children may cause in falling against a cabinet, or running into it with a tricycle, a pound sandbag is used to strike the center of a closed cabinet door and repeated with the door opened to a degree angle.
Shelves and bottoms are loaded at 15 pounds per square foot to ensure no excessive deflection or joint failure on the cabinet or mounting system.